Corn Puffed Extruder Machine-manufacture,factory,supplier from China

1. Before operating the corn equipment bulking machine, remove the head, movement, lead screw and other parts, clean them up, dry them and then install them.2. Idling for 1 to 2 minutes first when operating, put the raw materials into the feed mouth, not too fast, when the ring groove of the spiral shaft head is filled, stop feeding, friction preheating. Wait until the nose temperature rises and the pressure inside the cabin builds up before feeding.3. Feed should be continuous and uniform, material must be dry, must pay attention to.4.

As a food processing equipment, the food extruder has many precautions in use. For example, we need to remove the machine head, movement and lead screw before starting the operation, and we must carefully clean the rice on the machine. dirt and oil, and then re-installed. Only in this way can the material reach the required state and quality. So in the process of Jinan puffing extrusion equipment operation, what should we pay attention to?Matters needing attention during the operation of the extruder are:1. Mainly use corn and potatoes as raw materials to produce small food.2.

Extruder belongs to a kind of equipment for processing puffed food. It is a kind of equipment for processing puffed food, such as processing rice, corn, soybean, wheat, etc., in daily life.

The puffed foods such as potato chips, french fries, etc. that we usually see are produced by the puffed food extruder. After a series of operation procedures, the delicious food is presented in front of us.

Puffed food appeared in the market in the 1960s. Later, it quickly became popular in various countries because of its unique taste, simple eating and various patterns. It has long occupied the most frequently purchased snack types with chocolate, wafers and other foods.However, the long-term sales advertisements and puffed food have left us with a stereotyped image. Recently, many consumers said that when they saw the product category as "oil-containing puffed food", they were very worried about whether it was an unhealthy snack.

Extruder is the key of extruding technology. Extrusion processing technology as an economical and practical new processing method is widely used in food production, and has been rapidly developed. Extrusion processing mainly by an extruder step to complete the raw material mixing, curing, crushing, sterilization, pre-drying, molding and other processes, to make puffed, organized products or not puffed products.

Screw extruder is mainly used in the production of starch extruded food, protein extruded food and extruded feed in the food industry, and can also be used as a special chemical or biochemical reactor.Starch puffed foodThe starch in the grain will gelatinize (αize) under the high temperature and pressure of the extruder. The results showed that the degree of starch αization was more than 98% and the crude fat decreased by 60% or even disappeared after the puffed corn flour. Water solubility increased by more than 40%. Therefore, extruder can replace roller dryer to produce gelatinized starch.

Food puffing machinery production line mainly uses potato starch, corn starch, flour as raw materials, using a unique extrusion molding process, the production of the popular market of various shapes of the secondary puffed food. Mechanical production line design is reasonable, high degree of automation, accurate extrusion parameter control. The main machine is equipped with high and low pressure screw, which increases the scope of use of raw materials, reduces cost and improves product quality.

Feed extruder is a single screw extruder. Mainly used for food puffing, livestock feed or used for puffing single raw materials, but also as a plant oil and drinking wine production of raw materials in the pre-place. Twin-screw extruding extruder, mainly used for the production and processing of high-grade aquatic products, pet materials, especially the processing of viscous materials.What are its characteristics?1.

When operating a twin-screw extruder, it should be maintained on time. The maintenance process is carried out after the twin-screw extruder runs continuously for 2500-5000h and shuts down. The screw is extracted to inspect, measure and identify the wear condition of the most critical components, replace the components that have reached the specified wear limit as soon as possible, and repair the damaged components . The maintenance standard of the reducer of the twin-screw extruder is the same as that of the ordinary standard reducer.